Industrial Open CO2 Laser Cutting & Engraving Machines
WOOD & ACRYLIC
High-precision enclosed CO2 laser cutter for clean wood & acrylic cutting
FABRIC & TEXTILE
Multi-function laser cutter with auto-feeding mechanism for roll materials.
Rotary & Cylinder
Optional rotary attachment configurations for engraving
Industrial Heavy Duty
Factory-direct open laser machines built for 24/7 continuous operation.
High-speed belt drive CO2 laser machine CE certified for industrial reliability
High-precision rack drive CO2 laser cutter direct factory supply
High stability ball screw CO2 laser for wood, acrylic & leather
High power back drive flatbed CO2 laser cutter smooth acrylic edge cutting
High-speed belt drive CO2 laser machine CE certified for industrial reliability
High-precision rack drive CO2 laser cutter direct factory supply
High stability ball screw CO2 laser for wood, acrylic & leather
High power back drive flatbed CO2 laser cutter smooth acrylic edge cutting
COMMON PROCESSING ISSUES? HERE IS JOWUEY'S INDUSTRIAL SOLUTION.

1.ROUGH EDGES & BURNS
Standard cutters fail to cut through, leavingsevere burn marks on wood and acrylic
JOWUEY: 100‑200W RECI Tubes +0.2‑0.4MPa High‑Pressure Air Assist for clean with minimal burn.

2. SIZE INCONSISTENCY
Unstable mechanical frames cause non-circularshapes and varying cut sizes on full sheets.
JOWUEY: Heavy-Duty Rigid Chassis &Motion Systems for accurate, high-precision results

3. ACCURACY & ALIGNMENT
Ordinary cutters lose mark points andmisalign patterns, causing white edges onprinted materials.
JOWUEY : 1:1 High-Precision CCDCamera Vision System ensures exactedge following.

4. SLOW MANUAL FEEDING
Repetitive material feeding and manual focuseduce daily output and efficiency.
JOWUEY : Conveyor Auto-Feeding Table& Smart Auto-Focus for non-stopautomation.
Need help with your production challenges?
Our specialists will match a suitable laser machine for your actual production needs.
Engrave & Cut A Wide Range Of Materials With Our Laser System
Ideal For All Kinds Of Custom Projects






























View,Compare and Select
Watch video demos of different laser machine series
Our Laser
Open CO2 Laser Cutting Machine | ||||
Category | ||||
Model | ||||
Benefits | Belt drive fast speed and economic | Rack and Pinion Drive,High precision and long service life | Ball Screw Drive,High Precision and High Stability | Auto-feed, continuous processing |
User | Ideal for workshops seeking efficient and cost-effective cutting | Suited for production lines needing stable, accurate large-area cutting | Ideal for small to medium businesses with intricate designs | For small to medium workshops handling large-format materials |
Power | 100W 150W 300W 600W | 100W 150W 300W 600W | 100W 150W 300W 600W | 150W |
Material | Suitable for processing non-metallic materials such as acrylic, wood and fabric | Suitable for processing non-metallic materials such as acrylic, wood and fabric | Suitable for processing non-metallic materials such as acrylic, wood and fabric | Suitable for cutting non-metal materials such as fabric, cloth, and leather |
Cutting speed | 600mm/s | 600mm/s | 600mm/s | 833mm/s |
Engraving speed | 1200mm/s | 1200mm/s | 1200mm/s | 1000mm/s |
World's Greatest Customer Support



FAQ
Q1: How to solve white edges when cutting materials?
A1: Adjust the air valve to reduce the blowing pressure at the laser head.
Q3: Selection of focus lens focal length: Which is suitable for engraving, and which for cutting?
A3: 50.8mm is used for engraving.
63.5mm is for cutting plates below 10mm or for engraving.
101.6mm is for cutting plates of 10-20mm.
127mm is for cutting plates of 10-30mm.
Q5: What causes poor cutting quality?
A5: 1. Insufficient processing power setting.
2. Whether the focal length setting is accurate.
3. Whether the optical path is deviated.
4. Whether the laser head or focus lens is locked tightly.
5. Check for mechanical looseness and gaps in X and Y axes.
6. Check if the user parameters on the software are too high.
Q7: Why is there no laser output from the tube?
A7: 1.Check if the chiller is powered on.
2. Check if the water protection line is connected.
3. Check if the power is set on the software.
4. Test forced laser output from the power supply to determine if it’s the power supply or tube issue.
Q9: How to troubleshoot laser interruption during operation?
A9: 1. During processing, use a multimeter to check if the laser output signal terminal on the motherboard has consistent voltage or any changes.
2. Test the continuity of the chiller protection wine connector with a multimeter; and perform processing test with short circuit wire to observe any changes.
3. During processing, use a multimeter to measure whether the signal terminal of the laser power supply has consistent voltage or any changes.
4. If none of the above are issues, the problem is likely with the laser tube.
Q2: When processing a full sheet, why do multiple cut pieces have inconsistent sizes?
A2: 1. Uneven material placement.
2. Excessive bed flatness error.
3. Inaccurate step distance.
4. Check for mechanical looseness and gaps in X and Y axes.
5. Motor step loss.
6. Driver issue; test by array-copying multiple rectangles and observe overlap accuracy.
Q4: How to adjust the focal length?
A4: Move the focusing lens barrel up or down until the dot on the material is at its finest point, indicating the correct focal length.
Q6: What models of reflective mirrors and focus lenses are used for 150W, 180W, 300W? What focal length do they represent?
A6: For 150W, the reflective mirror is 25 and the focusing lens is 20*63.5 with an 8mm focal length.
For 180W, the reflective mirror is 25 and the focusing lens is 20*63.5 with an 8mm focal length.
For 300W, the reflective mirror is 30 and the focusing lens is 25*127 with an 18mm focal length.
Q8: Laser head can’t move left and right, click the control panel does not respond.
A8: 1. The X-axis limit switch is faulty. Find the limit switch on the left side of the X axis and check whether the wiring and contact rod of the limit switch are in good condition.
2. X-axis motor interface contact is poor. If the X-axis limit switch works properly, open the upper right door panel of the machine and check whether the interface of the X-axis motor is connected correctly.
3. X-axis motor or drive is damaged. Open the lower right door panel of the machine and check whether the red LED light on the X-axis driver flashes
Q10: The exhaust fan cannot exhaust smoke.
A10: 1. Install the air inlet and outlet in the opposite direction.
2. Check whether the exhaust fan is faulty is to directly connect the power supply, use the power cable of the water tank to connect the exhaust fan power cable connector, and then connect the power supply to check whether the exhaust fan can work normally.
Contact
After sales service
Get your quote for affordable CO2 laser cutters, cheap CO2 laser engravers, best CO2 laser cutting machines, and best budget CO2 laser engravers. Find the right CO2 laser cutting machine for sale or CO2 laser engraver for sale to handle wood, plastic, marble, glass, mdf and other non-metal materials.”
Quick contact
Follow us
Get your quote
Our representative will contact you soon.